Friday, June 25, 2010

How to modify a Korg Monotron



So here's how to modify Korg's new Monotron analog ribbon synthesizer. Perhaps this is the first document of Monotron mods in Europe since it still hasn't been released here.

It's actually a very easy machine to modify because for whatever reason Korg decided to label all the interesting points on the bottom side of the PCB. This may well have been for testing units at the factory/service centers. Perhaps though it could have been that the designers anticipated this little machine would be hacked, much like the Gakken which pretty obviously inspired this piece. Incidentally in the magazine that comes with the Gakken there's a picture of them showing it to Korg, that was in 2008, go figure.

Modification wise everything is simple enough except for the gate. Unfortunately the gate point affects the pitch somewhat. There's a few solutions, the first of which is to use a single pitch cv line into the gate socket. This will work but you wont be able to get really low notes which is less than useful.

After a little research I came across an idea to use a dtc114 transistor to trigger the gate (soldered at a different point). I tried this but didn't have much success. Also that method will result in the LFO not re-triggering which is bad since the LFO is the closest thing to an envelope on the machine.

By far the simplest solution is to use something like Silent Way by Expert Sleepers (see my previous video on this software) or Volta by Motu. After calibration there's no issues whatsoever and the monotron tracks over 5 octaves nicely.

Using an adjustable dc power supply is a good alternative to the batteries and is also useful in getting the Monotron to a decent tuning range, just don't dial in more than 3 volts. I built my power supply based on this schematic

If you intend to use both battery power and dc power you should include some diodes in your design.

And lets not forget the filter, the side of the packaging says "the legendary MS-20 filter" while this is true design wise it would probably be more accurate to say the MS-10 filter since it's only low pass and the MS-20 has low and high pass filters. How does the filter sound? actually very good! I've repaired some MS units and the Monotron really does have some DNA from the MS series, even down to the small noise hiss when the resonance is high but not yet self oscillating.

A couple of things I noticed about the filter input, if you drive the input signal too hard the resonance almost disappears, so be sure not to overdrive it too much if you want the full character of the filter. Also the input jack is stereo which means if you use a Y cable you can run two signals into the filter comfortably. I tested to see if the left side input leaked to the right input and it doesn't at all, which means it really is a true stereo input to the filter which is very nice.

As for the output, even though it's a mono output via a stereo jack the manual states that you shouldn't use a mono jack on the stereo output, so it's probably best to use a stereo jack plug but leaving the ring floating to get a mono signal into your daw/mixer. The output is a little noisy due to the fact that its really a headphone out and the output level is a little low so you will probably want to use a noise gate to remove the noise floor when it's not playing. (this is the same with the Gakken)

That's about it, here's the diagrams for modding, as you can see it's very simple indeed and should be no problem for anyone with soldering skills.

The Monotron should be available to buy in Europe from around the 30th of June for around 50-60 euros.



138 comments:

  1. Could you run this mc-202 to mod to monotron then?

    ReplyDelete
  2. @ richardrich

    how do you mean cv/gate control? yes you could but tuning would be midrage, you wouldnt get any low notes and scale might be a little bit of an issue.

    ReplyDelete
  3. Wow, thanks for this. I just bought a Monotron today in Toronto, Canada, and I modded it tonight using your schematic. Then I downloaded Silent Way and got busy!

    I like your 4-pin DIN, but I can't help but think there might be something better. For now I just cut a small opening in the back of the Monotron's case and soldered the leads directly to the jack box with the resistors.

    It works beautifully, and the Monotron sounds really great. I'll probably put something on Youtube over the next few days, once I get used to Silent Way.

    ReplyDelete
  4. Thank you very much for your instructive work!

    ReplyDelete
  5. Thanks for this ! It opens new monotronic dimensions !

    ReplyDelete
  6. Absolutly excellent video - thanks.

    I am looking at building a Baby 10 with 555 trigger - shoud I want to drive the Monotron can I simply send the CV out from the Baby 10 - to the CV-Pitch input of the Montron? Do I need to worry about the CV voltge - I was planning on running it on a 9V battery ..

    Appreciate any guidance..

    s.

    ReplyDelete
  7. You'll need to measure the baby10 outputs and attenuate to suit, I wouldn't run more than 5v into the monotron tbh. Check my diy seq also here on the blog, it's based on the baby10

    ReplyDelete
  8. can you explain how to use something like silent way - do you calibrate the monotron or whatever is sending the signal? i don't think its an option for me either way.

    if i was to control this using the cv/gate from my x0xb0x would i not get the full note range?

    ReplyDelete
  9. Hi - I have got the Baby10 in production - and will use a simple voltage divider to ensure the actual CV levels only run from 0-5 volts.

    Looking at your schematics I am unsure how to take the single CV out from the Baby10 - and use it for CV/Gate - is the Gate just getting the same CV pulse signal to trigger the note ? Sorry if this seems a basic uestion - just want to fully understand what I am doing before I start hacking the Korg.

    Thanks, Stephen.

    ReplyDelete
  10. @derek

    silent way is a computer plug in, you can read about it here http://www.expert-sleepers.co.uk it uses your audio interface as a cv/gate converter and the calibration routine is part of the plugin.

    as for using the x0x, itll work but you may find teh tuning scale is wrong.

    ReplyDelete
  11. @ farmer glitch

    you can just use two resistors to attenuate the output, its quite simple, tie one to ground and the other inline.

    Yes you can use the cv line as a gate, use your cv line and plug it into the gate socket and dont use the gate line from your controller. If that doesnt work well you'll have to create a cv mixer to mix the cv and gate, which can be done very cheaply with an opamp and a few resistors (provided you have a bi-polar power supply)

    ReplyDelete
  12. Thanks for posting this howto,

    I've used your schematic to connect my monotron to an arduino.

    I am using a digital pin for gate and for pitch i'm using the PWM output.

    I have two problems at the moment:
    The gate is interracting with the pitch so some notes sound a bit odd.
    And tuning of the cv seems to be difficult too. Do you, perhaps, have some tips??

    ReplyDelete
  13. OK - think I get it- I guess I can simply take the 9 volt pulse from the 4017 of the Baby 10 - before I run it to the pot - and send that - shoud this also be 5 volts max - and I guess I'll need diodes on each pin too ?

    So I understand the top Jack input and bottom jack input of your scematic - are simply controlling the trigger and pitch - please can you clarify what the middle jack input is doing ?

    Many thanks again ..

    ReplyDelete
  14. Do you have a mouser part number for that 4 pin DIN, and the cable that would hook up to it?

    ReplyDelete
  15. Thanks for the video and schematic, works great!

    ReplyDelete
  16. I was hoping to use the monotron with a Kenton midi CV converter-gate is 5 volts on 0 volts off and CV is one volt per octave. Will the gate voltage be too high? There is an auxillary CV also on the Kenton which I hope to use for filter cutoff. Any suggestions from people? The monotron has a surprisingly nice and unique tone and it would be cool to control vibrato and "wah" from a midi keyboard via aftertouch and mod wheel. Looking at the photos of it's innards,the entry point of the ribbon to the board looks tantalizing for mod points don't you think,cos that could attend to gate and pitch from the one entry point? Or am I talking rubbish!
    Cheers Ross

    ReplyDelete
  17. is the CV volt/octave or linear like the MS-20?

    ReplyDelete
  18. Not to be too pedantic but 1v oct is linear, the ms20 is logarithmic. But in answer to your question, it's 1v oct

    ReplyDelete
  19. Quick question about the output:
    It's a stereo jack, but a mono output? How does that work? If you feed a stereo signal into the filter, does that mean it's summed back out as a mono output?

    ReplyDelete
  20. its a stereo jack output and it clearly states in the manual not to use a mono jack so i wouldn't recommend doing otherwise.

    ReplyDelete
  21. would it be ok to use a stand alone 3V DC power supply for this?

    ReplyDelete
  22. @ronan, probably but to be on the safe side make sure its a low ampage, 300ma or less and also that its a regulated power supply, it would be worth checking it on a meter since some supplys put out a lot more than what they are rated for. It would most definately be a better idea to build the power supply since you'll get a nice regulated and controllable suply then.

    ReplyDelete
  23. I'd like to do this mod, and it seems relatively easy. However, the CV output of my analogue sequencer (a Mochika 2.1) is in the form of a 1/4 jack, not DIN. So er... how would I go about this? Would a jack-to-DIN cable be sufficient to do the trick?

    ReplyDelete
  24. you dont need to worry about din, im just using that to connect the external box to the monotron, the external box is where you would connect your seq and you could just build that box with 1/4" instead of 1/8" jacks

    ReplyDelete
  25. What range of voltages can you feed into the CV inputs of the monotron? 0-3V, 0-5V or something else?

    ReplyDelete
  26. can you run through how you wired the din in relation to positive and ground terminals?

    also, i'm a little unclear as to whether the minijacks in the ext. box need to be grounded or not.

    ReplyDelete
  27. @Tonias 0-5v works fine

    @ronan

    its not really important whats wired where in teh din cable as long as the source and destinations match up. Ie, you wire the cv in to pin 1 and wire pin 1 to the cv in point on the board etc.

    And yes the mini jacks need to be grounded to the monotron ground else external signals wont work.

    ReplyDelete
  28. that's all clear but when using external power do i wire the negative dc wire to monotron ground also?

    ReplyDelete
  29. Hey Guys I just found this - http://www.fengland.org/mm.html
    If anyone was still having trouble with finding a MIDI solution ;]

    ReplyDelete
  30. @ronan yes the DC negative is wired to ground of course else theres no circuit ;)

    ReplyDelete
  31. it's my first build if you hadn't guessed, first of many hopefully. thanks! :)

    ReplyDelete
  32. cool, good luck its one of the more simpler mods

    ReplyDelete
  33. Wow, this is a great mod. I bought a monotron a couple months back and gotta say that for $60 odd bucks you're getting a great piece of synth. Gonna buy another and try your mod!

    If you're interested I've got a review of the monotron here: http://gamesounddesign.com/korg-monotron-hand-held-synth-for-sound-design.html

    Cheers!

    ReplyDelete
  34. hye i just bought myself a monotron...is the anyway that i can use it with my guitar and boss gt 10 efx?

    ReplyDelete
  35. Thank you for this great article. I'm about to get a Monotron (it's on its way from the US), and this video made me want it even more :)

    I don't see why you have to attenuate the output as you can supply a HCF4017BE (this is what I got) anywhere from 3V to 15V, and the output voltage is almost (0.05V less) equal to Vcc. Or am I just missimng something here? :)

    ReplyDelete
  36. @Anubus there's no 4017 in this mod, unless you are mixing it up with the step seq?

    ReplyDelete
  37. Yes, but didn't you say (in the comments here) you had to attenuate the output of your Baby10-clone sequencer to 0-5V so it matches the CV input of the Monotron?

    ReplyDelete
  38. ah well i did that since i use it with my modular and it make a lot more sense to have a 5v range there

    ReplyDelete
  39. I guess it was my fault to place the comment there :) But yeah, the 4017 works with 5V just fine.

    ReplyDelete
  40. Nice video!

    Is it possible to rig up the Monotron
    whit a Kenton Pro-SOLO MkII to get midi control and
    have them build in them to new case, and then feed
    them both with DC from this PSU unit

    (PSU data)

    Power supply with adjustable output voltage:
    0-12V. Max 5A. Input voltage 15V AC

    link to the psu unit (with picture)

    http://www.kjell.com/content/templates/shop_main_
    details.aspxitem=87184&path=&sms_ss=email&at_
    xt=4cc9c029cfbefe24,0

    Note! with this psu unit the device will need two
    of them, otherwise I can't feed the monotron and
    the kenton at the same time whit DC... not so
    convenient, but it works I think.

    if this works to together, is then possible with
    this setup to add more features (to add a full VCO section, full LFO section, full VCF section, full
    AMP evelope section, full Evelope 1&2 section +
    maybe add a patch feld to make it patcheble)

    to the monotron whitout changing the Psu or
    adding more of them?


    ///Daniel Fletcher of D a z z - S y n t h

    ReplyDelete
  41. @daniel that PSU will still require an ac/ac adaptor and its rather expensive (as i find most stuff at kjell is, cheap junk tbh) better to build a twin adjustable and run it from a single ac/dc adaptor then you can run two sources from it.

    ReplyDelete
  42. oh and for the kenton i dout you will get a usable pitch range (that'll be in tune) much better to use silent way or volta

    ReplyDelete
  43. Thank you so much for putting this up! I moded mine to work with my modular setup in one night! Such a blast.

    Thought I'd record some of the nastier things the Monotron can do and post it for people to check out if you're on the fence about picking one up:

    http://www.youtube.com/watch?v=0aJy1aQiAcU

    Cheers!

    ReplyDelete
  44. Hi 2cv et ALL,

    Clarification needed:
    1) because the Gate voltage affects pitch. I'm assuming that using a Kenton Solo Midi to CV adapter would limit the note range to whatever the Gate voltage is coming from the Kenton (5v gate)...soooo...
    2) Couldn't I wire inline a variable potentiometer to adjust the output voltage of the gate coming from the Kenton?. IE. trimming down the Gate voltage to 2 or 3 volts to allow for lower notes?
    3) you mentioned using a single CV line into the gate. Why isn't this a fix-all solution if a linear voltage was sent thru the CV line at 1v\OCt? I notice that the gate lower threshold is around 1.2v.
    4) Has anyone used another CV source successfully and had decent scaling? I am unhappy with Silent Way. The PC version needs many improvements and crashes Cubase 5.5 on my machine in an almost predictable pattern..
    5) I've been in contact with Forrest England, the creator of the Midi mod for this thing, and it seems that he's nipped all scaling issues with his mod. What can be integrated to the current CV schematic that would correct this issue?

    Thanks all for your input...

    Erik

    ReplyDelete
  45. @ Daniel Westin, any luck with Kenton...?

    ReplyDelete
  46. itll only go so far, its not just about the voltage but the tuning scale, with the kenton its 1v per octave, thats to say each additional volt will increae the pitch by an octave. This is why most 1volt/oct analog synths will have two trimmers internally, one for the base pitch and another for the scale. Such trimmers do not exist in the monotron.

    ReplyDelete
  47. @ Sablerock

    soory but I had'nt have the time to try this thing out yet, but me and my synth technician will try it out soon.

    I will tell you all about it, when we are done.

    Cheers!

    ///Daniel Fletcher of D a z z - S y n t h

    ReplyDelete
  48. Is where any one how have a suggestion on witch parts what I can use with the monotron?

    Im thinking about chips for a extra VCO's and a VCO part what can complete the build in VCO, and when a VCF part what can complete the VCF sektion, + Something for the LFO sektion, last but final a whole Amp envelope sektion + 2 ADSR Envelopes

    Is SEM chips a good choice, or is where something better?

    Cheers!

    ///Daniel Fletcher of D a z z - S y n t h

    ReplyDelete
  49. Hi Guys!

    I’ve started a Monotron forum. It’s a place where people can discuss Monotron mods, hacks, as well as other synths.

    Check it out: http://monotron.adornomedia.com/

    –David

    ReplyDelete
  50. Korg have posted the Montron schematics fyi...

    http://www.korg-datastorage.jp/Manual/monotron_sch.pdf

    =)

    ReplyDelete
  51. excellent find Ben, I'll take a look at doing a proper line out when i have time now instead of the crappy headphone out.

    ReplyDelete
  52. 4017 works from 3v to 18v so you can drive anything as long as you change the supply voltage accordingly :)

    ReplyDelete
  53. 2cv thanks so much, i bought a monotron just because of this!

    so i have been having a great time with the mod (here is a quick 3 x guitar-CV-monotron demo: http://www.megaupload.com/?d=Y8U7GKP5 )

    quick questions though in case you have the time:

    1. i noticed that if you send a pitch CV into the cutoff CV input, it tends to swoop in and out of range really quick (which is strange since the cutoff tracks across a more extended range when you just control the cutoff and the pitch at the same time with the switch)... do you happen to know what range of resistors/rheostat might do the trick to get the cutoff CV input to track a little more "broadly"?

    2. how hard is this 5V input CV rule? in my excitement, i tried the setup first with my theremin which puts out a 10V gate (it worked with no apparent damage, although the theremin sounds sort of lame with an on/off gate), and now my guitar setup uses an 8V gate... i've been playing for hours like this with no problems -yet-... do you think this is a bad idea?

    ReplyDelete
  54. i wouldnt drive it too hot, consider that its onyl really a battery operated unit so you might cook something. Somesort of attenuator would be a good idea for hot signals.

    when adding cv to the vcf dont forget that its only addign to the existing voltage set by the cutoff knob and the lfo intensity, setting them lower should yield better results.

    ReplyDelete
  55. thx for the reply!! you have convinced me to overcome laziness and open everything back up - i added a 330k resistor to the gate input and another 330k to the cutoff input - the math might not be quite right, but it seems to work great. (cutoff still needs a rheostat to get the filter tracking better, but it seems to be close)... thanks again for all of your help!

    ReplyDelete
  56. Hi Guys!

    I found something that is really good for this kind
    of thing this blog is about...

    I will use this device for my own Monotron
    "expansion modul" prodject that I have started
    up with an pro synth engineer...

    what I found, is device the gives your montron power (psu power) + it also gives you a CV/MIDI interfac
    at the same time.

    and the good thing about it is that, it only coast's 79:- euro

    + with this device you can also add extra futures to your monotron lika a VCA, or a ENV gen etc. you
    chould even get a full VCO or VCF/LFO. With this
    device you can add up to 8 diffrent modules of euroracks to it...

    In theory with this device you could make a monster synth with the montoron as the main sound engine...

    where is only one expression that can explain this:

    "This is way to cool for school"


    here is a link to the device.

    http://www.mfberlin.de/Produkte/Module/Power/POWERe/powere.html


    Cheers!


    ///Daniel Fletcher of D a z z - S y n t h

    ReplyDelete
  57. hi Danuiel, yes those are great, i use two of them in my modular, MFB also sell 3u frame for this which is compatable to eurorack modules.

    ReplyDelete
  58. Hi 2cv,
    I'm having some problems calibrating my monotron with silent way. Could you possibly export your silent way calibration file and place it somewhere for us to download? I'm just interested to see if using your calibration template will result in some usable tones for me.
    thanks!

    ReplyDelete
  59. really busy over the next few days but i'll see what i can do over the weekend or early next week, remind me if i forget ;-)

    ReplyDelete
  60. Hello all. How will you fix the audio out on the monotron? Is there a schematic (general) to adapt to fixing the headphone output?
    I'd love to run other audio through this little machine for recording, as the filter really brightens and fattens things up.

    ReplyDelete
  61. So I successfully de-linked the gate from the pitch CV by removing one of those tiny resistors... basically if you are "pretty competent" with SMD soldering you can just follow these instructions (see the section entitled "at first"):
    http://beatnic.jp/monotron/midi-kit.html

    if you are only "marginally competent", you will do what i did and accidentally disconnect the gate CV pad from everything and the monotron amp will just stay "on" regardless of input... a workaround is to run a wire to bring the gate CV input directly to the big IC (see the schematic, if i recall pin 10?).

    although the built-in keyboard strip will not trigger the gate after this, the gate CV input will properly trigger both the amp and LFO. and the tiny keyboard will still affect pitch if something else is triggering gate.

    finally, although i posted earlier i was using a 330k resistor to lesssen my gate CV, i am finding that, if you are like me and using an analogue systems envelope follower to generate the gate CV, you need A LOT more resistance to cut the signal to workable voltage range.

    has anybody gotten a clean signal out of the monotron? i read from somewhere that you can avoid the noise by connecting to the middle pin of the volume pot, but in my quick experimentation i didn't have any luck with that...

    ReplyDelete
  62. @ Jeff , I calibrated my monotron with silent way and got a usable range of 4 octaves with a behringer uca202 soundcard. Just copy/paste this in a *.txt file and it should work:

    Silent Way Calibration Data
    version: 1
    42 0.34889168
    43 0.40106520
    44 0.43328676
    45 0.46550831
    46 0.49772987
    47 0.51377177
    48 0.52858740
    49 0.54340303
    50 0.55821866
    51 0.57303429
    52 0.58784986
    53 0.60266548
    54 0.61748111
    55 0.63008136
    56 0.64039880
    57 0.65071619
    58 0.66103363
    59 0.67135102
    60 0.68166846
    61 0.69198585
    62 0.70230329
    63 0.71262074
    64 0.72293812
    65 0.73325557
    66 0.74357295
    67 0.75323087
    68 0.76179922
    69 0.77036750
    70 0.77893585
    71 0.78750420
    72 0.79607248
    73 0.80464083
    74 0.81320918
    75 0.82177746
    76 0.83034581
    77 0.83891416
    78 0.84748250
    79 0.85605079
    80 0.86461914
    81 0.87318748
    82 0.88102514
    83 0.88866681
    84 0.89630842
    85 0.90395010
    86 0.91159177
    87 0.91923338
    88 0.92687505
    89 0.93451667
    90 0.94215834
    91 0.94979995
    92 0.95744163
    93 0.96508330
    94 0.97272491
    95 0.98036659
    96 0.98800820
    97 0.99564987

    ReplyDelete
  63. @2Cv

    Does the the MFB psu/Midi to CV unit comes whit pre programed midi part or do I need to program the midi part my self?

    ///Daniel Fletcher of D a z z - S y n t h
    www.myspace.com/dazzsynth

    ReplyDelete
  64. Hi youp, thanks for the post i will try this, because me too having hard time to do calibration, i always get saw or sine wave type. I've checked the voltage with my multi, the voltage indicate for exemple : if i'm test only the gate cv line alone with nothin else pluged i read 4 volt, as soon as i put another cv line lets say vcf cv line 10 volt, the voltage go reverse into the gate cv line and my reading give me also 10 volt or so in the gate cv line, is it the monotron gate problem or i did a bad soldering on the pcb ??

    ReplyDelete
  65. I'm new to synths, so I don't actually intend to modify my monotron, but I wanted to find out what you meant about overdriving the filter. How do I avoid overdriving? Is input from my computer's sound card going to be too much for the monotron's filter to handle without damage?

    ReplyDelete
  66. @Hazel

    what i mean by overdriving is sending a signal that is too loud.

    ReplyDelete
  67. @2Cv

    So basically, as long as I keep the volume of whatever device is outputting the signal fairly low, the filter should be fine?

    ReplyDelete
  68. you also dont want to drive it too low to keep the noise level down, best to experiment and see how far you can push it, I found that if the signal was too high the resonance disapeared.

    ReplyDelete
  69. Hi,
    how can I get rid of the noise on the monotron?
    Is there a way to improve S/N?
    Does it help to skip the voltage coverter 3V/5V and to apply a yet higher voltage to the circuit. Anyone tried?

    ReplyDelete
  70. does this mod allow for the proper retriggering of lfo when it receives gate?

    ReplyDelete
  71. yes lfo is retriggered with each gate sent

    ReplyDelete
  72. @ ipc.de
    The noise seems to be from the filter circuit.
    Check this thread for more info.
    http://www.muffwiggler.com/forum/viewtopic.php?t=26319&postdays=0&postorder=asc&start=0

    ReplyDelete
  73. Hey, can anyone suggest what's happening here? :
    I'm endeavoring to get the monotron working with my Kenton pro2000mkii and with it set to volts\oct it seems to be moving the monotron in the wrong direction -- ie higher note from kenton = lower pitch on monotron. any ideas??

    ReplyDelete
  74. -Runs to maplins to destroy my montotron!- I was getting a bit fed up of the sound now this I can work with! I could use one of my monotron's midi sequencers with a bit of work to add a new external machine! wooohoo!

    ReplyDelete
  75. what about the other labeled points on the board? is there anything useful i can do with them?

    ReplyDelete
  76. and could you post a pictures of the inside of the breakout box? i cant figure out what i'm doing wrong...

    ReplyDelete
  77. Hey Nice video.

    I'm gonna use:
    1) a photocell and 3v on Cutoff
    2) a photocell and 0,7v on Rate(Lfo)(for precicer control)

    Can u please tell me howmuch Ampère I need for rate and cutoff?

    Would be really helpfull.

    ReplyDelete
  78. Anyone mod the VCO pad yet? I've not seen any mod tap off this line and I'm not clear if it's the raw VCO output or VCO 'input' hope it's the latter.

    ReplyDelete
  79. @ youp / 2CV

    Hey, to get a Behringer UCA202 or similar interface working with Silent Way, do you have to use AC Encoder with some modified cables?

    ReplyDelete
  80. hi my monotron only works with a mono output. could you clarify why this may be ?

    ReplyDelete
  81. Sorry to resurrect this but I've got the same problem as James posted last year. Namely, the higher the note I play on my MIDI keyboard, the lower the pitch of the monotron. My MIDI-CV is definitely outputting 1v/oct as normal. I'm tearing my hair out - any ideas?

    ReplyDelete
  82. Hi, sorry to bother with what could be a stupid question, but using the gate and cv out of my doepfer Dark Energy I can control the gate, but the pitch and the cutoff do not work. I can control the pitch with the LFO of the dark energy but not through the pitch jack,only through the cutoff. Any ideas? please help

    ReplyDelete
  83. sorry everyone for not replying on teh many questions here, not had time and it feels like such a long time ago that i did this :)

    @James

    iirc the gate affects the pitch, so perhaps your gate is too hot.

    @Aaron sorry, id rather not take it apart now ;) the schematic shows everything.

    @brammeown not much, certainly in the low ma area

    @Trevor Nunes it might be the raw vco, cant remember sorry.

    @Charlie Kemp thats a question for the silent way forums i think ;-)

    @soulvent its mono yes but you should use a stereo output according to the manual.

    @robman84 i suspect the gate signal is too hot

    @Plaxid are you using cv1 on the rear of the dark energy?

    ReplyDelete
  84. thanks for the 'how to'
    it works great triggering from my SH101
    I don't really understand what I did but it's fun
    I can't play well tempered scales from that Cv in Monotron stuff but the 303 effect is here
    someone may leave an answer, please, if there is something I can do to get more precise octaves and other intervals
    thx

    ReplyDelete
  85. Help!..I did the mod (Gate and pitch cv only). I'm triggering using a PAIA Fatman but there is no change at all in the notes if I play in my keyboard lets say a do..re..mi...in the PAIA you hear a do..re..mi...but in the korg I only hear a fa..fa..fa..any comment will be more than appreciate it...Thanks in advance..Sid

    ReplyDelete
  86. Hi!
    I've build the GATE IN circuit replacing the on-board SMD resistor that connects the ribbon with gate input with a diode, adding one also on my input.
    There are no problems with pitch and the frequencies go nicely low.
    some rough, rough pics:
    http://www.teck.niezba.org/?s=objekt&o=016_-_K-mono_prototype&c=red

    ReplyDelete
  87. Hi! I've built a Midi Master Clock, that sends sync24 as well. How should I wire it up to Monotron in order to have a synced LFO?

    http://gieskes.nl/master-clock-generator/images/sync24-Schematics.gif

    My guess would've been: start/stop to the LFO, Clock to RATE, and ground obviously to GROUND. Is this correct?

    Regards,
    Asko

    ReplyDelete
  88. I've never done a mod on anything before, but it really looks like my monotron will be capable of some good stuff if I do it. Would this be a possibility for someone who has never tried messing around with a PCB?

    ReplyDelete
  89. Hi there!

    Thanks for this.
    I'm currently doing this mod and I'm not quite sure what the 10K pot is doing. It doesn't make any difference whether or not it's on the breadboard (testing stage still!). I've tried different values...nothing.

    ReplyDelete
  90. Hello!
    I was thinking about using the Monotron as a filter for a Atomosynth Mochika (Stepseq/Synth). Is there a way to mod the Monotrons LFO to sync up to the Mochika? It has Gate/Clock and CV outs. Any ideas?
    Thank you fine people in advance :)

    ReplyDelete
  91. I am about to try to mod this unit. Thank you for all the useful info. I was wondering, has anyone tried to add a CV input to the LFO rate and Amount?

    ReplyDelete
  92. Hello! By adding the CV/Gate i unintentionally created a theremin-like effect. When i come near the Monotron with my hands the pitch changes almost a halftone. Do you have an idea what could cause this problem? Best regards, Pike

    ReplyDelete
  93. Hi, I would love to make this mod and some pictures of the insides of your monitor & custom case would be so great to have and I think a help to many noobies such as I.

    This would be my very first DIY project and I really need step-by-step instructions and can not find them anywhere. Like what should I buy (resistors, switches etc) and more.

    Would be great if I could get that!!

    Thanks so much!!

    ReplyDelete
  94. I of course mean MONOTRON and not MONITOR.

    ReplyDelete
  95. I feel like I have watched every Monotron mod youtube clip, read every forum post and blog but I can't find the answer to what is probably a simple question. I feel this is best place to ask.

    I have no experience with electronics.

    I have an MS-20 mini and the Monotron. Can I simply cut and solder one end of a 3.5mm mono cable to each of the Pitch, gate and cutoff cv points of the monotron and plug these into the Keyboard CV out, Trigger out and an envelope or LFO generator of the MS-20?

    As they are both from Korg, do they both use the same CV format ie. Hz/v.

    Most the mods seem to include other boxes, power, extra diodes and other things. Are these neccessary for controlling the Monotron from an ms-20

    ReplyDelete
  96. Thanks so much for this mod. I built one this weekend using your page + this one:

    http://www.synthsync.com/monotron-create-external-cv-gate-inputs/

    ReplyDelete
  97. Hi
    I have tried and failed to get anything other than the gate to work so far i am however modding a monotron delay but i believe gate and pitch are identical? I can gate it but cannot get it to trigger without using the ribbon, so no pitch triggering at all. I am using a beatstep pro cv and gate but i have seen others using an sh101 but doesnt the monotron require s trig not v trig? Anh help greatly appreciated

    ReplyDelete
  98. Hi, I performed your mod and had success - also a decent scaling for a couple of octaves. After some days (and remake some bad solderings in the gate-cv-cutoff points on the monotron pcb) I now realize that there's a low frequency noise like hum when I play the monotron or even if sequenced externally. It seems a ground or shield noise, and it seems that monotron is sensible to my hands too, this noise goes up and down depending on where I touch it. It's present only when the VCA opens.
    Frankly I don't know if I could have slightly damaged some components while soldering the cables, or the cables are not enough shielded (they come from a cat. 5 network cable). I took ground from the battery negative pole on the PCB.
    Batteries are ok. While remaining in the background the noise is badly mixing with the monotron oscillator, and sometimes if I touch the external connector used for CV/gate/cutoff connection (5 pin din) on its ground pole, this hums reduces a lot. What could be happening?
    Thank you
    Maurizio

    ReplyDelete
  99. you can also use reaktor to send cv out fyi

    ReplyDelete
  100. I really like reading through a post that can make people think. Also, many thanks for permitting me to comment! 먹튀검증

    ReplyDelete
  101. Just wanna comment that you have a very nice internet site , I love the design it actually stands out. Unique Dofollow Backlinks

    ReplyDelete
  102. I just want to say I’m new to blogs and certainly savored this blog site. Very likely I’m planning to bookmark your blog . You amazingly have fantastic articles. Thanks for sharing your blog.야동

    ReplyDelete
  103. Very good article! We are linking to this particularly great content on our site. Keep up the great writing. Pretty valuable material, overall I consider this is worth a bookmark, thanks 대딸방

    ReplyDelete
  104. "It has a good meaning. If you always live positively, someday good things will happen. Let’s believe in the power of positivity. Have a nice day.횟수 무제한 출장

    ReplyDelete
  105. Nice post. I learn something totally new and challenging on sites I stumble upon every day. 타이마사지

    ReplyDelete
  106. Oh my goodness! Incredible article dude! Many thanks, However I am going through difficulties
    with your RSS. I don’t know the reason why I cannot join it.
    Is there anybody getting identical RSS problems?

    Anyone that knows the solution will you kindly respond?
    Thanx!!Click Here 오피월드


    3YOUNGYANG

    ReplyDelete
  107. It's really great. Thank you for providing a quality article. There is something you might be interested in. Do you know 먹튀검증? If you have more questions, please come to my site and check it out!


    ReplyDelete
  108. This is the perfect post.사설토토사이트 It helped me a lot. If you have time, I hope you come to my site and share your opinions. Have a nice day.


    ReplyDelete
  109. What a post I've been looking for! I'm very happy to finally read this post. 메이저사이트추천 Thank you very much. Can I refer to your post on my website? Your post touched me a lot and helped me a lot. If you have any questions, please visit my site and read what kind of posts I am posting. I am sure it will be interesting.


    ReplyDelete
  110. What a post I've been looking for! I'm very happy to finally read this post. evolution Thank you very much. Can I refer to your post on my website? Your post touched me a lot and helped me a lot. If you have any questions, please visit my site and read what kind of posts I am posting. I am sure it will be interesting.


    ReplyDelete
  111. I have taken your writing very well. Where can I get this information? I want to write good writing like you. Would you like to be a guest blogger on my website?
    야설

    ReplyDelete
  112. This website and I conceive this internet site is really informative ! Keep on putting up! 일본야동

    ReplyDelete
  113. 카지노사이트
    It proved to be very useful to me and I am sure to all the commenters here! That's a good post. This article contains detailed information on this topic. I have read all your information. Thank you for your good work. Please visit my site and send us your comments. ajude meu site

    ReplyDelete
  114. "If you are planning for best contents like me, just pay a simple visit this website everyday for the reason that it presents quality contents, thanks"

    성인야설
    오피헌터
    출장안마
    타이마사지
    카지노사이트

    ReplyDelete
  115. Your web site is great. I was extremely touched by this post. I'm so pleased to locate the write-up I have actually been seeking for a long period of time. I covet the amount of individuals sympathize with your writing. You discover a great deal of expertise from my writing. 온라인카지노

    ReplyDelete
  116. Thanks to the wise criticize. Us & our next-doors ended up only getting ready to accomplish a little analysis on this specific. เว็บบาคาร่า อันดับ1

    ReplyDelete
  117. สูตรทุจริตบาคาร่าออนไลน์ 2022 คนไหนกันต้องการร่ำรวยจำต้องไม่พลาด
    เกมบาคาร่ายอดนิยมกันในทุกวันนี้ มีผู้เล่นมีความสนใจเยอะมาก แล้วก็ใช้แบบอย่างการเดินเกมที่ไม่เหมือนกันขึ้นกับแนวทางการพินิจพิจารณาเกมของผู้เล่นแต่ละท่าน บางคนก็ใช้สูตรบาคาร่า แต่ว่าก็ยังมีบางคนที่แทงพนันแบบมั่วๆอยู่ ซึ่งนักเขียนไม่เสนอแนะเพราะเหตุว่ามันจะเสียตังค์โดยไร้ประโยชน์ นักเขียนก็เลยมีสูตรบาคาร่ามาแจกให้ โดยที่ไม่ผิดกฎข้อตกลงมาฝากกัน

    ตอนแรกมาทำความรู้จักกับ บาคาร่าออนไลน์ กันก่อน
    เกมบาคาร่าออนไลน์ ก็คือ เกมที่ใช้ไพ่สำหรับเพื่อการพนันผลแพ้ชนะระหว่างข้างสีแดงเป็น 'เจ้ามือ' สีน้ำเงินก็คือ 'ผู้เล่น' ซึ่งการจั่วจะจั่วข้างละ 2 ใบ ถ้าหากผลบวกการจั่วออกมาแล้วข้างใดมีแต้มเลข 9 หรือใกล้เคียงเลข 9 มากยิ่งกว่ากัน ข้างนั้นก็จะชนะ แล้วก็คนที่พนันข้างนั้นไปก็จะได้รับเงินรางวัลไป นี่เป็นกรรมวิธีเล่นบาคาร่ากล้วยๆยอดนิยมจากผู้เล่นมือใหม่ รวมทั้งสามารถเข้าถึงผู้เล่นได้หลายชนชั้น เนื่องจากว่าสามารถเล่นจากในสมาร์ทโฟนก็ได้ รวมทั้งใช้เงินสำหรับการพนันปริมาณน้อยก็สามารถเล่นได้แล้ว

    สูตรบาคาร่าฟรี ใช้ง่าย เห็นผล
    สูตรบาคาร่าออนไลน์ มีเยอะแยะหลายสำนัก แต่ละสำนักก็จะได้ผลต่างกัน บางสำนักก็มีสูตรที่จะต้องเสียตังค์บ้าง ซึ่งผู้เล่นควรทำการศึกษาเรียนรู้และทำการค้นคว้ากฎข้อตกลงในแต่ละคาสิโนให้ดีว่าไม่ถูกกฎข้อตกลงหรือเปล่า แต่ว่าสำนักของพวกเรามีสูตรที่จะมาแจกให้ใช้แบบฟรีๆไม่เสียค่าใช้จ่าย และไม่ไม่ถูกกฎข้อตกลงด้วย โน่นเป็น 'สูตรบาคาร่า AI 2022' ซึ่งเป็นสูตรที่ใช้ระบบการคำนวณข้อมูลทางสถิติ ความเป็นไปได้มาเก็บเป็นฐานข้อมูล แล้วก็ประเมินผลออกมาได้ผลที่จะออกล่วงหน้าให้ผู้เล่นได้รู้

    การใช้แรงงานสูตร AI 2022
    ความเที่ยงตรงสำหรับในการคำนวณของสูตรบาคาร่าออนไลน์ มีสถิติออกมามากถึง 99.99 % ความคลาดเคลื่อนน้อยมากๆการทำงานด้วยระบบ AI artifcial intelligence สามารถทำเงินให้แก่ท่านได้อย่างที่จิตใจอยากได้ ในการใช้งานให้แก่ท่านเข้าไปสมัครใช้ระบบ เลือกคาสิโนที่ปรารถนาเล่นจากนั้นเลือกห้อง ห้องโปรแกรมสูตรจะประกอบไปด้วย
    เลขที่ห้อง, สถานะเกมเวลานี้, รอบเกม รวมทั้งอัตราการเอาชนะโดยจะแสดงผลลัพธ์เป็นเปอร์เซ็นต์ตามอัตราการชนะ เมื่อเลือกห้องได้แล้วให้เล่นบาคาร่าพร้อมกันกับโปรแกรมสูตร โดยให้ลงแทงดังที่ตารางสูตรได้บอกมา จะมีสถิติชนะอยู่ขวามือ สถิติที่แพ้ก็จะอยู่ซ้ายมือ

    การใช้สูตรคดโกงบาคาร่าออนไลน์ 'AI 2022' นี้ได้ผลได้ค่อนจะเกือบจะ 100 % อย่างไรก็ตามผู้เล่นควรที่จะเลือกห้องที่มีอัตราการชนะสูง เพื่อสร้างความเชื่อมั่นและมั่นใจสำหรับการเล่นเยอะขึ้น รวมถึงจะต้องมีการจัดการการใช้เงิน คิดแผนอย่างรัดกุม แล้วเดินเกมไปตามแผน รับประกันได้ว่าผู้เล่นจะบรรลุผลสำเร็จสำหรับการเล่นบาคาร่าอย่างไม่ต้องสงสัย

    ReplyDelete
  118. สล็อตออนไลน์กับค่าย Pgslot ที่คุณจะต้องเข้ามาเลือกเล่นเป็นขั้นแรก
    การเล่นเกม Pgslot นั้นต่างเป็นที่ชอบใจของเหล่าผู้ที่อยากได้เข้ามาใส่ความบันเทิงใจ เข้ามาเล่นเกมคาสิโนออนไลน์ และก็เพื่อเป็นการเพิ่มช่องทางสำหรับในการทำเงิน เพิ่มจังหวะสำหรับในการทำความเข้าใจกับเกมคาสิโนออนไลน์พวกนี้ ผู้เล่นจำเป็นจะต้องศึกษาเล่าเรียนในแนวทางการเล่น รู้จักจัดแจงเล่นเกมคาสิโนออนไลน์ กลุ่มนี้มาให้เหมาะสมที่สุด เพราะว่ามันจะช่วยทำให้ผู้เล่น สามารถเล่นเกมพีจีสล็อตได้บันเทิงใจเพิ่มขึ้นเรื่อยๆ ได้โอกาสสำหรับการทำเงินได้ง่ายดายมากยิ่งกว่าเดิม มันยังไม่ใช่แค่นี้ก่อนที่จะผู้เล่นจะเข้าไปสมัครเล่นเกมคาสิโนออนไลน์ พีจีสล็อต
    จำเป็นที่จะต้องเล่าเรียนเกี่ยวกับเกมคาสิโนออนไลน์ที่คุณพอใจให้ดี เพื่อเป็นการเพิ่มจังหวะสำหรับในการทำเงิน แล้วก็ลดความบกพร่องที่อาจจะมีการเกิดสังกัดเกมที่คุณปรารถนาเล่น สรุปว่าวันนี้ แม้คุณปรารถนาเล่นเกมสล็อต พวกเราจะไปทำความเข้าใจเกี่ยวกับเกมลักษณะนี้ พื้นฐานกันเลย
    เกมสล็อตออนไลน์ Pgslot ในตอนนี้
    Pgslot เป็นต้นแบบเกมที่น่าดึงดูด รวมทั้งได้รับการปรับปรุงแก้ไขปรับปรุงมาจนถึงทุกวันนี้ ด้วยเหตุว่ากล่าวได้เลยว่า เกมสล็อต ที่เล่นอยู่เป็นเกมที่ดีเยี่ยมที่สุดเกมหนึ่งเลยก็ว่าได้ไพเราะเพราะพริ้ง ด้วยลักษณะของเกม แล้วก็รายละเอียดของเกม นั้นมีความต่าง มีความน่าเล่น ในตัวของมันเอง pgslot ขึ้นกับผู้เล่น ถูกใจเล่นสล็อตแนวไหน รวมทั้งเว็บไซต์ของพวกเราจะปรับปรุงระบบ ให้มีความง่ายดายมากยิ่งขึ้น อยู่เสมอเวลา ไม่ให้ขาดตกบกพร่องที่ตามมาตอนหลัง พวกเรามิได้จะปรับปรุง หรือเพียงแค่แก้ไขระบบ แต่ว่าพวกเราจะปรับปรุงต้นแบบเกมให้น่าเล่น อยู่เสมอเวลา ทั้งยังภาพ และก็แบบอย่างรายละเอียดที่จะต้องไม่เหมือนกับสล็อตในแบบอย่างเก่า
    เหตุเพราะตอนนี้ ที่คนถูกใจเล่นสล็อตออนไลน์กันเยอะขึ้น ทำให้พวกเราจำเป็นต้องปรับปรุงปรับแต่งให้มีความนำสมัยตามเวลาอยู่อย่างสม่ำเสมอ เพื่อง่ายแล้วก็สบายต่อการใช้แรงงาน ก็เลยทำให้ในตอนนี้สล็อตเลยเป็นคุณลักษณะเด่นที่ทำให้เว็บไซต์ พีจีสล็อต มีคนเข้ามาเล่นกันจำนวนมากกว่าเว็บไซต์อื่นๆ
    ข้อควรคิดสำหรับเพื่อการเล่น Pgslot
    แน่ๆว่า นักเล่นการพนันหลายท่าน ก็อยากได้ที่จะมีสูตรเพื่อนำไปต่อยอดการเล่นของตนให้ดี หรือเรียกกล้วยๆเป็นการมีแนวทางที่ใช้สำหรับในการชนะเกมสล็อต จากเว็บไซต์ Pgslot ซึ่งสิ่งที่พวกเรากำลังจะบอก คุณสามารถ ปฏิบัติตามได้อย่างง่ายๆ เพียงแต่คุณจำเป็นต้องทราบจุดเด่นสำหรับการเล่นสล็อตนี้ซะก่อน โน่นเป็น การมีวินัยสำหรับในการเล่น พีจีสล็อต ด้วยเหตุว่าโน่นเป็นอีกหนึ่งเหตุผล ที่หลายๆคนถูกใจเอ่ยถึงว่า ‘เล่นพนัน เป็นไปไม่ได้ร่ำรวย ขึ้นได้’ เนื่องจากว่าคุณไม่มีระเบียบสำหรับเพื่อการเล่น เพราะว่าถ้าเกิดคุณเล่นเสีย จะก่อให้คุณนั้นมีลักษณะอาการรำคาญและก็อยากได้เงินคืน คุณเลยจำต้องเพิ่มเพื่อจะเล่นใหม่ แม้กระนั้นโน่นเป็นสิ่งที่ทำให้ท่านบางทีอาจเสียตังค์ไปโดยใช่เหตุ
    ฉะนั้นคุณควรจะมีสติสำหรับการเล่น แล้วก็มีความบใคร่ครวญตนเอง เนื่องจากโน่นเป็นสิ่งที่คุณควรจะทำตั้งแต่เริ่มการพนันหนแรกตราบจนกระทั่งจบเกมพนันตามปริมาณที่คุณอยาก

    ReplyDelete
  119. จุดเด่นจากการได้รับเครดิตฟรีเพื่อร่วม บาคาร่า
    ในตอนนี้การร่วมเล่นเกมพนันออนไลน์ หรือ บาคาร่าเป็นที่ชื่นชอบอย่างยิ่ง รวมทั้งการได้รับเครดิตฟรีก็ถือได้ว่าเร่องที่นักเสี่ยงโชคโดยมากมีความสนใจ ถ้าเป็นแบบนี้แล้ว การได้รับเครดิตฟรี ถือได้ว่าเรื่องที่ดีเลิศๆแล้ว และก็การนำเครดิตฟรีไปใช้ก็ถือได้ว่าเรื่องที่สำคัญอย่างยิ่ง รวมทั้งห้ามให้ขาดเลยเด็ดขาดๆที่ผู้เล่นจำเป็นต้องเรียนรู้ให้ดีก่อนจะมีการเริ่มพนัน
    การได้รับเครดิตฟรี บาคาร่ามีจุดเด่นเช่นไร
    เมื่อนักการพนันที่ชื่นชอบเกี่ยวกับการเล่นเกมการพนันออนไลน์อยู่แล้วนั้น ได้รับเครดิตฟรี นักการพนันก็สามารถที่จะนำเครดิตฟรีที่ตัวนักเล่นการพนันได้ ไปต่อยอดในเกมการพนันในรอบการพนันที่คุณลงเล่นได้เลย
    ต่อทุนสร้างรายได้
    ถ้าเกิดคุณได้รับเครดิตฟรีบาคาร่าแล้วนั้น คุณสามารรถยนต์ที่จะนำเครดิตฟรีที่ได้รับไปเป็นทุนต่อยอดให้กับตัวเองได้เลย หรือถ้าเกิดผู้เล่นต้องการจะให้เครดิตฟรีที่ได้มานั้นบรรลุเป้าหมายจริงๆผู้เล่นควรที่จะนำไปเล่นกับเกมที่ผู้เล่นถนัด ทราบ แล้วก็รู้เรื่องลักษณะของเกมอยู่แล้ว ด้วยเหตุว่าผู้เล่นสามารถจับทางของเกมได้แล้วว่าผลการพนันจะออกยังไง เพราะว่าตัวเองกำเนิดความเคยชิน ถ้าเป็นแบบนั้นแล้วจังหวะกระบวนการทำเงินสร้างรายได้ของนักเล่นการพนันก็อยู่ไม่ไกล และก็กระบวนการนี้จะก่อให้คุณได้เงินจริงๆอีกด้วย
    เพลิดเพลินใจกับเกมที่ตัวเองพอใจ
    ด้วยเหตุว่าเกมบาคาร่า พนันออนไลน์เป็นเกมที่มีแบบอย่างให้เลือกเล่นนานาประการ เนื่องจากได้ปรับปรุงขึ้นมาเพื่อรองรับแก่ความชอบพอของตัวนักเล่นการพนันแต่ละบุคคล เนื่องจากผู้เล่นแต่ละคนมีความนิยมที่ต่างกันออกไป ทำให้ผู้เล่นสามารถเลือกเล่นเกมที่ตัวเองชอบพอ แล้วก็นักการพนันก็ยังสามารถที่จะนำเครดิตฟรีไปใช้เพื่อการพนันได้เลย แล้วในรอบการพนันนั้น ถ้าเกิดผู้เล่นได้ร่วมพนัน แล้วผลของการพนันออกมาว่าชนะผู้เล่นก็สามารถรอคอยรับเงินจริงได้เลย สามารถได้เงินจริง เร็ว เข้าระบบUSER ของเพศผู้เล่นเลย บาคาร่า
    การได้รับเครดิตฟรีนับว่าเป็นเรื่องที่ดีเลิศอย่าง ที่ผู้เล่นโดยมากกำลังกล่าวถึงเหลวให้ความเอาใจใส่มหาศาลเพราะเหตุว่าเกมพนันออนไลน์นี้ เป็นเกมที่มอบเงินจริง แล้วก็หากผู้เล่นได้เริ่มพนันโดยที่ใช้เครดิตฟรีที่ได้รับนั้น นับว่ายิ่งเกิดเรื่องที่ดียิ่งขึ้นไปอีก ด้วยเหตุว่าคุณจะได้พนันในรอบการพนันจริง ที่มิได้ใช้เงินลงทุนของตนเป็นการสร้างรายได้ และก็ถ้าส่งผลการพนันออกมาว่าชนะการพนันผู้เล่นสามารถที่กำลังจะได้รับเงินรางวัลไปท้ายที่สุด

    ReplyDelete
  120. บาคาร่ากับการตั้งเป้าหมายที่ทำให้ประสบความสำเร็จ บาคาร่า
    เป้าหมายในการเล่น บาคาร่าเป็นสิ่งจำเป็นที่ต้องมี เพราะว่าเกมเหล่านี้ทำให้เกิดความสนุกสนานเพลิดเพลิน จนอาจจะทำให้เราเสียเงินได้หากเราหลงเข้าไปในความบันเทิงของเกมประเภทนี้ การตั้งเป้าหมายก็เพื่อเป็นตัวกำหนดว่าเมื่อไหร่ที่เราต้องหยุดเล่นเดิมพันแต่ละครั้ง และเป็นการตั้งความต้องการของเราให้ชัดเจนว่าในการเข้าเล่นแต่ละครั้งเราต้องการเงินกำไรเท่าไหร่ รวมถึงหากเราเสียเราลงทุนไปเท่าไหร่เราควรหยุดเล่น
    เป้าหมายในการทำกำไรต่างจากเป้าหมายในการเสียเงิน
    การเข้าเล่นเดิมพันบาคาร่า ทุกคนต้องเรียนรู้ไว้ว่าการได้และเสียมันสามารถเกิดขึ้นได้ทุกครั้ง ดังนั้นการตั้งเป้าหมายจึงไม่ได้ตั้งแค่เพียงการทำกำไรเท่านั้น แต่เป้าหมายในการเล่นเสียก็มีความจำเป็นไม่ต่างกัน หลายคนอาจมองว่าทำไมจะต้องตั้งเป้าหมายในการเล่นเสียเอาไว้ด้วย มันเหมือนกับการแช่งตัวเองหรือเปล่าซึ่งไม่เหมาะกับการเสี่ยงดวงแบบนี้
    แต่เป้าหมายในการเล่นคาสิโนเสียไม่ได้เป็นสิ่งไม่ดีแต่มันจะเป็นตัวช่วยอีกตัวสำหรับคนที่อยากทำเงินจากเกมเดิมพันเหล่านี้ เพราะคุณต้องกำหนดเอาไว้เลยว่าหากคุณเสียเงินเสียไปเท่าไหร่คุณควรหยุดเล่น เพราะถ้าคุณไม่มีเป้าหมายหากเล่นเสียคุณก็จะหยุดตัวเองไม่ได้และพยายามที่จะตามทุนคืนจนในที่สุดอาจจะเสียมากกว่าเดิมได้นั้นเอง ในส่วนของเป้าหมายในการทำกำไรทุกคนคงรู้กันอยู่แล้วว่าควรจะตั้งแบบไหน
    เป้าหมายในการทำกำไรเท่าไหร่จึงจะเหมาะสมกับทุน
    การตั้งเป้าหมายในการทำกำไรจาก บาคาร่าคุณไม่ควรตั้งเอาไว้สูงเกินไป เพราะหากเป้าหมายกับเงินทุนไม่เหมาะสมกัน จะทำให้ผู้เล่นกดดันตนเองมาเกกินไปจากที่จะได้จะกลายเป็นเสียทันที ดังนั้นลองมาดูกันว่าเป้าหมายที่เหมาะสมกับทุนควรเป็นอย่างไร ดังนี้
    • ในการเข้าเล่นเกมเดิมพันใน คาสิโน
    เป้าหมายที่เหมาะสมคือคุณต้องทำกำไรให้ได้อย่างน้อย 1 – 3 เท่าของเงินทุนที่คุณมี ยกตัวอย่างเช่น คุณใช้เงินลงทุน 200 บาทกำไรที่คุณควรหาได้คือ 200 – 600 บาท เมื่อทำได้แล้วควรหยุดเล่นทันที
    • หากคุณอยากได้กำไรเพิ่มขึ้นคุณจะต้องเพิ่มทุนไม่ใช่เพิ่มเป้าหมาย
    หลายคนที่เพิ่มเป้าหมายให้แก่ตนเองหลังจากที่ประสบความสำเร็จมาแล้วในช่วงแรก ๆ ที่เข้าเล่นเดิมพัน แต่จริง ๆ แล้วคุณไม่ควรเพิ่มเป้าหมายเพียงอย่างเดียวแต่คุณต้องเพิ่มเงินทุนที่เหมาะสมเข้าไปด้วย เช่น ช่วงแรกคุณใช้ทุน 100 บาท ทำกำไรได้ 300 บาท ต่อไปคุณใช้ทุน 300 บาท และกำไรที่คุณตั้งหมายควรเป็น 300 – 900 บาท เป็นต้น
    • หากคุณเล่นเดิมพันแบบทบทุนเป้าหมายคุณจะเปลี่ยนแปลงตลอด
    การเล่นเดิมพันใน คาสิโน คุณสามารถใช้วิธีการเล่นแบบทบทุนได้ แต่เป้าหมายของคุณจะต้องคอยเปลี่ยนไปเงินที่คุณลงทุนด้วยเช่นกัน เช่นคุณใช้เงินลงทุนบาคาร่าทั้งหมด 200 บาท คุณใช้เงินวางเดิมพันต่อรอบที่ 5% ของเงินทุนทั้งหมด หรือ 10 บาทต่อรอบ เมื่อคุณทำกำไรได้เท่าตัวของเงินทุนแล้วจะเท่ากับคุณมีเงินทั้งหมด 400 บาท ต่อไปคุณต้องเพิ่มเงินลงทุนเป็นรอบละ 20 บาท และอาจจะเพิ่มขึ้นเรื่อย ๆ เมื่อทำกำไรได้ 1 เท่าของทุนในรอบนั้น ๆ แล้ว ดังนั้นการตั้งเป้าหมายแบบง่าย ๆ กับวิธีการเล่นแบบนี้ คือตั้งเป้าไว้เลยว่าเมื่อทำกำไรได้รอบที่เท่าไหร่จึงควรหยุดเล่น อาจจะกำหนดไว้ที่ 3 – 5 รอบในการเพิ่มเงินทุนเพียงเท่านี้คุณก็จะรู้แล้วว่าเมื่อไหร่คุณควรหยุดนั้นเอง

    ReplyDelete
  121. บาคาร่าเกมพนันคาสิโนที่เล่นจำนวนกี่ครั้งก็สนุกสนานทุกหน บาคาร่า
    สำหรับในการเล่นเกมคาสิโนจะให้มีความเพลิดเพลินได้นั้น ก็จำเป็นต้องกล่าวว่าอยู่ที่ขาพนันว่าขาพนันนั้นถูกใจเกมพนันในต้นแบบใด เพราะเหตุว่าถ้าหากว่าเลือกเล่นเกมพนันที่ผิดหัวใจแล้วล่ะก็ แน่ๆว่าเล่นไปและก็ปราศจากความสุขอย่างแน่แท้ ซึ่งพวกเราขอยกตัวอย่างให้ขาพนันได้เห็นภาพในเรื่องของความพอใจในเกมพนัน เช่น เมื่อขาพนันให้ความสนใจกับเกมบาคาร่าอย่างมากมาย แม้กระนั้นเนื่องมาจากเกมบาคาร่านั้นครั้งคราวก็มีการจ่ายพนันที่ค่อนข้างจะสูงถึงแม้ว่าจะจ่ายเพียงแต่หลัก 10 ในแต่ละเกมที่เล่นพนัน แม้กระนั้นเมื่อขาพนันมีเงินทุนที่น้อยก็มีความสำคัญที่จะจำเป็นต้องเล่นเกมสล็อตแทนที่เป็นเกมที่ใช้เงินที่ใช้ในการเดิมพันในปริมาณที่น้อยกว่า ด้วยเหตุนี้ เมื่อขาพนันเข้าไปเล่นและจำเป็นต้องบอกได้เลยว่าขาพนันจะปราศจากความสุขสำหรับการเล่นอย่างแน่แท้
    บาคาร่าเกมพนันที่ยิ่งเล่นก็ยิ่งได้รับฟรีเครดิตเพิ่ม
    บางเกมในเกมคาสิโนนั้นยิ่งเล่นก็มิได้รับฟรีเครดิตเลย แต่ว่าในที่นี้พวกเราขอชี้แนะให้ขาพนันเล่นเกมบาคาร่าเลย เนื่องจากว่าเกมบาคาร่ายิ่งเล่นขาพนันก็ยิ่งได้ฟรีเครดิต เหตุที่เป็นแบบนี้เพราะบาคาร่าที่ขาพนันเล่นนั้นต้องมีการเติมเครดิต แล้วก็การเติมเครดิตนี่เองที่เป็นสิ่งที่ทำให้ขาพนันได้รับเงินฟรีๆอย่างราบรื่น
    บาคาร่าออนไลน์เว็บไซต์ที่เล่นเยอะแค่ไหนก็มีแม้กระนั้นได้แค่นั้น
    เกมพนันที่พวกเราเล่นอยู่กันในขณะนี้นั้น แน่ๆว่ามีเสียแล้วก็มีได้สลับกันไป แต่ว่าถ้าหากขาพนันหาเกมที่เล่นแล้วมีแม้กระนั้นได้มากกว่าเสียขาพนันก็จะต้องเลือกเล่นเกมบาคาร่าแค่นั้น ซึ่งง่ายสุดๆๆเลยเพียงแต่ขาพนันเข้าไปในเว็บไซต์พนันออนไลน์เพียงแค่นั้นขาพนันก็ได้เล่นเกมบาคาร่าที่ขาพนันอยากแล้ว
    โดยเหตุนี้ เว็บไซต์บาคาร่าออนไลน์ในขณะนี้ ไม่ว่าขาพนันจะเข้ามาเล่นสักจำนวนกี่ครั้งก็ตามขาพนันจะทราบได้เลยว่ามีความสนุกสนานร่าเริงเป็นอย่างมาก เพราะว่านอกเหนือจากจะสนุกสนานในเกมพนันแล้ว ยังบันเทิงใจที่กำลังจะได้รับเงินฟรีเครดิตในทุกๆครั้งที่มีการเพิ่มเติมเงินที่ใช้ในการเดิมพันอีกด้วย แล้วก็เกมบาคาร่านี้บอกเลยว่าขาพนันสามารถที่จะให้ความไว้ใจได้อย่างดีเยี่ยม เพราะเว็บไซต์พนันที่มีในขณะนี้ล้วนแล้วแต่เป็นเว็บไซต์ที่มีความที่ได้รับความนิยม ซึ่งชี้ให้เห็นว่าความมั่นคงและยั่งยืนด้านการเงินของเว็บไซต์ก็มีความมั่นคงและยั่งยืนที่ดีอย่างยิ่งจริงๆ เนื่องจากว่าไม่งั้นแล้วคงจะขาดเงินที่จะให้เครดิตเงินฟรีแก่ขาพนันได้หรอก

    ReplyDelete
  122. รับเครดิตได้ แบบไม่มีเงื่อนไข เพื่อนำไปใช้ในการทดลองเล่นเกมจากเว็บไซต์ PGSLOTGAMES แจ็คพ็อตแตก โปรโมชั่นพิเศษสุดๆ เลือกเล่น ทดลองเล่นสล็อต PG ใหม่ และรับเงินได้ตาต้องการ เล่นได้ทั้งสมาชิกใหม่ และสมาชิกเก่า เอาใจทุกสายปั่นสล็อตที่ดีที่สุด

    ReplyDelete
  123. เกมสล็อตแตกง่าย เล่นได้ดั่งใจ ทำกำไรได้เลยผ่านเว็บ PGSLOTGAMES เล่นได้ทุกวัน เพิ่มโอกาสการได้รับเงินรางวัลที่มากขึ้น ทำได้ง่าย เงื่อนไขน้อย เล่นได้ไม่มีเบื่อ PG ทดลองเล่น ตอบโจทย์สายทุนน้อย พร้อมอัพเดตโปรโมชั่นใหม่ ให้ได้เล่นตามต้องการ

    ReplyDelete
  124. superslot แจกเครดิตฟรี 100 โปรโมชั่นร้อนแรง เว็บ สล็อต ตัวท็อป ติดอันดับ 1 ของประเทศไทย superslot สมัครรับโบนัสฟรีทันที เครดิตฟรี 100 เป็นทางเลือกที่มีไว้สำหรับ นักลงทุนที่กำลังหาทุนไปต่อยอดในการเดิมพันเข้าเล่นเกมเพื่อหารายได้ ทดลองเล่นสล็อต ทางเลือกที่เต็มไปด้วยประสิทธิภาพ อย่างโดดเด่นที่ชัดเจน

    ReplyDelete
  125. superslot 50 free credit, no need to top up, you can get it and still ทดลองเล่นสล็อต All games are free, more than 500 games. ทางเข้า superslot GET BONUS INSTANTLY

    ReplyDelete
  126. pg slot make money online games Is another entertainment, เล่นฟรี ไม่ต้องสมัคร, which allows players to play free slots games and get both fun. enjoy making money Thrilling with great bonus rewards That can tell that it's satisfying and should be hit.>>ทางเข้า pg slot

    ReplyDelete
  127. What a masterpiece ! check my web and learn how to get cash fast and secured ! 검증카지노

    ReplyDelete
  128. Thank you very much for your post, it makes us have more and more discs in our life, So kind for you, I also hope you will make more and more excellent post and let’s more and more talk,
    thank you very much, dear.
    검증카지노

    ReplyDelete
  129. Gambling can be done gambling with a minimum of 100 baht, which needs to be in a hurry to place all bets, gradually gamble with less money to look at the game's tier first. And even at that time, it looked good, how much bets could win, can throw at it. Maybe, maybe break the jackpot? pg slot

    ReplyDelete